Modix - BIG -180X 3D Printer - 1800x600x600mm

Modix BIG-180X

The Modix BIG-180 is a mix of large build volume and premium components, at an affordable price. Like the BIG-60 - Modix's flagship - it features all the latest components from Version3 and enjoys the same level of modular offerings to better match your needs and budget.

* Large printing room - 1800x600x600m

Specifications

* Duet 2 WiFi, a powerful 3D printer controller from the UK.

* FFF (Fused Filament Fabrication) - Print technology

* Similar core concept - All Modix printers share the same design (electronics, printhead, movement, etc.) and are based on the Modix BIG-60 V3.0

* Print head: single E3D Aero & E3D Volcano 1.75 mm

* Duet3D Wifi 32 bit controller

* 100 leveling points for automatic leveling of the building plate

* 4 X Z-axis motors are individually controlled, providing automatic build plate calibration

* Mounted on industrial wheels with dual function: open - rubber fits for stability, closed mode - wheels make it easy to roll on the floor

* Open top lid and large front doors for easy access to building chamber

*Secondary print head

Frame and Enclosure

* Solid T-slot aluminum profiles

* Powder coated laser cut aluminum fittings and assemblies

* Closed enclosure made of 3 mm black aluminum composite panels (ACP).

Motherboard

* Powerful 32 bit processor
* Dedicated Wifi module with external antenna
* Quiet TMC2660 stepper drivers, up to 256 microstepping.
* High speed uSD card and support for an additional external SD card if required.
* Double extruders on the main board, possibility of 5 more extruders on the expansion board.
* High power: Each stepper driver is capable of 2.8A motor current, currently limited in software to 2.4A.

* User-friendly – ​​7" Duet3d touch screen

* Internet access (WiFi) via remote control from mobile or PC, so that print files can be uploaded directly from your workstation

* SD card slot and USB

Movement system

* Hiwin MGW9H linear guide rails

* Four Z ball screws for Z axis 12mm diameter, 4mm pitch

* 9 mm Gates GT2 timing belt, reinforced with fiberglass

* Axis motor: Motech Nema17 60mm length MT-1705HS200A
(Holding torque: 8.2 kg.cm Current/phase: 2.00A)

* Positional Accuracy: X-10 Micron, Y-10 Micron, Z-0.5 Micron

* Print speed – Normal quality 60mm/sec, Pull 100mm/sec, Calculated for 0.4 nozzle.

Power

* Supports both 110V and 230V

* Meanwell 24V 280W power supply

* Protection: Short/ Overload/ Overvoltage/ Overheat.

* Power consumption without load <0.5W

* LED indicator for 'Power-On'

* Airplane quality switches and plugs

* Heated building plate AC powered heater 1370 Watt

Building plate

* 6.35mm thick, Alcoa Mic6 milled cast aluminum plate

* AC powered building board heater - 1370 Watt. Requires additional independent 15A AC source.

* Double heating zones. Internal 200X200mm size for small items and lower power consumption.

* Maximum temperature – 120°C

* Print surface – PEI sheet with 3M high temp. adhesive sheet.

Automatic leveling

* BL touch markings as standard

* Leveling of the build plate is stored in and activated before each print

* 100 leveling points

* The image shows the interface for the calibration process.

Here you can see that there is a need for a small upward movement of the rear left bed spring.

Software

* Open source Duet RepRap firmware. The leading firmware for 3D printing allows numerous configurations and easy customization using the macro system.

* One can choose from any available slicer and 3D printer controller including: Slic3r, Cura and Simplify3d (recommended).

Extrude
* E3D Aero extruder for both primary and secondary extruders.
* Configuration: Main – direct drive, secondary – direct drive.
* Extruder drive gear ratio 3:1 for power and accuracy.
* Nema17 - 40mm for high power extrusion.
* Adjustable tension wheel.

Dual print head

* Secondary printhead enables printing of complex models that require easy removal. That is models with internal geometry. For these prints, the 3D Expert recommends using a secondary printhead that can print with soluble filaments that would later be removed with water.

See our selection here

Hot End

* E3D V6 Volcano high-flow heat block – standard
* Optional E3D V6 for very small objects with small details or Super Volcano for high-speed, high-flow printing and for printing bulky objects
* 1.75 mm filament diameter is standard, but can be changed to 3 mm
* 0.4, 0.6 & 0.8 mm brass Volcano nozzles
* Smaller nozzle diameters are available for standard V6
* 24V 40W Heater cartridge, max temperature is 285°C as standard. Can be converted up to 500°C, by changing the thermistor if necessary

* 5015 fan

På linket nedenfor, finder du en mappe med alt dokumentation for 3D printere, filamenter mv. Den vil løbende blive opdateret

Klik her og gå til dokumentation

Du kan få leveret din ordre til en valgfri GLS pakkeshop, privats- eller erhvervsadresse.

Vi leverer din ordre fragtfrit til en valgfri GLS pakkeshop, hvis du bestiller for over 399 kr.

Du har mulighed for at vælge afhentning i butik. Når du modtager en mail med at din ordre er færdig pakket, kan den afhentes indenfor vores åbningstider, som er mandag til torsdag 9-17.00 og fredag kl. 9-16.30 på vores adresse Amalienborgvej 57 i Nørresundby.

Vil du vide mere om vores returregler, læs dem her

Vi ser frem til din ordre 😍